Latest Papers

ASME Journal of Mechanisms and Robotics

  • Fully Foldable Mechanical Metamaterials With Isotropic Auxeticity and Its Generated Multi-Mode Folding Form
    on February 10, 2025 at 12:00 am

    AbstractAuxetic materials, a type of mechanical metamaterial with negative Poisson's ratio, are potentially utilized in the realms of energy absorption and engineering structures. However, most of the existing auxetic materials either contain a large amount of rotational motion or still have gaps when fully folded, which is not conducive to lifting loads. Besides, their application is limited to flexible environments due to their single-folding mode. To overcome such limitations, a fully foldable mechanical metamaterial with isotropic auxeticity is proposed by utilizing the Sarrus mechanism, and a derivative multi-mode folding form is obtained in this paper. Then, the degrees-of-freedom (DOF), bistability, and kinematic characterizations are analyzed to show the performance of the proposed structures. Finally, the parameters of the proposed fully foldable mechanical metamaterials are discussed to simplify the structures. Some prototypes are fabricated to validate the effectiveness and performance of the proposed mechanical metamaterials. The proposed mechanical metamaterials have some merits, such as isotropic auxeticity, being fully folded to achieve dense compression, being bistable with load-bearing capacity, multi-mode folding form, and single-DOF, and they have versatile potential applications in complex environments requiring large deformation and flexible adaptation.

  • Elastostatic Performance Evaluation of a Full-Mobility Parallel-Kinematics Machine With Flexible Links
    on February 10, 2025 at 12:00 am

    AbstractThe subject of this article is the elastostatics of a novel three-limb, full-mobility parallel-kinematics machine (PKM) with flexible links, intended for high-frequency, small-amplitude operations. The objective is to establish the Cartesian stiffness model and performance indices capable of guiding the structural design of the machines of interest. We base our analysis on what we term an elastostatic Cartesian model: the light-weight limb rods are modeled as identical, massless, linearly elastic beams; the motor shafts and couplings are modeled likewise, with the beams replaced by identical, massless, linearly elastic torsional springs, both link flexibility and actuator flexibility thus being considered. The moving platform is assumed to be the only moving rigid body of the machine. This platform is thus regarded as a rigid body elastically mounted onto the base platform via a six-degree-of-freedom (six-DoF) Cartesian spring. Then, the PKM 6×6 Cartesian stiffness matrix, considering the flexibility of both limb rods and motor shafts, is derived via the pertinent kinetostatic relations. Moreover, three alternative indices are defined from this model to evaluate the robot stiffness, which allows us to choose the most appropriate one for specific applications.

  • Announcing the Journal of Mechanisms and Robotics 2023 Best Paper Award
    on February 10, 2025 at 12:00 am

    JMR Best Paper for 2023

  • Active Cables Selection for Collocated Vibration Control of Small-Sized Overconstrained Cable-Driven Parallel Robots
    on February 10, 2025 at 12:00 am

    AbstractCable-driven parallel robots (CDPRs) are well appreciated for high dynamics applications, due to their lightweights moving parts. Nevertheless, due to the low stiffness of cables, vibrations can occur and can degrade performances if high precision is required, such as in additive manufacturing for instance. Previous works have studied techniques to counteract vibrations, like using motor command or embedded devices. Based on a previous first exploration of using piezoelectric transducers on cables for this type of robot, this paper presents a proper formulation of the collocated active vibration control to damp the end-effector oscillations of small-sized overconstrained CDPRs by the measure of the variation in cable tensions. This goes through a modeling of such a robot with embedded piezoelectric transducers under appropriate assumptions. From this control formulation, it is shown that the collocated nature of these transducers are fundamental. It is thus possible to highlight an energetic index of active cables selection, regardless of the used control law. The proposed technique is developed theoretically and analyzed through simulations on an eight-cable robot.

Force-Motion Coupled Mechanism Synthesis Method of Heavy Load Parallel Kinematic Mechanism for Multi-DoF Forming Process

Abstract

At present, the design of parallel kinematic mechanism (PKM) generally starts from type synthesis based on the motion pattern and then the dimensions are synthesized based on performance requirements. The synthesized type of PKM with optimal load-bearing capacity is hard to determine because the above type synthesis is just based on the motion pattern and the number of synthesized types of PKM is huge. Therefore, this paper aims to investigate a force-motion coupled mechanism synthesis method for heavy-load PKM with optimal motion performance and load-bearing capacity. First, the optimal load-bearing conditions for PKM are derived, namely, the wrench screw of a limb is parallel to the external force acting on the moving platform and is reciprocal with the wrench of the actuator. Furthermore, a novel force-motion coupled type synthesis method is proposed, in which the wrench of the limb is added to the constrained screw system. In this situation, the synthesized PKM is singular. Therefore, dimension synthesis is carried out based on the workspace, and a near-singular 6-PHSS PKM is then synthesized. Finally, a novel multi-DoF forming machine with a forming force of 6000 kN is developed. Compared with the Stewart platform (6-UPS PKM), the maximum forces of the actuator and limb of the new near-singular 6-PHSS PKM were reduced by 80% and 10%, respectively, validating the proposed force-motion coupled synthesis method for heavy-load PKM.

Read More

Journal of Mechanisms and Robotics Open Issues