Latest Papers

ASME Journal of Mechanisms and Robotics

  • Fully Foldable Mechanical Metamaterials With Isotropic Auxeticity and Its Generated Multi-Mode Folding Form
    on February 10, 2025 at 12:00 am

    AbstractAuxetic materials, a type of mechanical metamaterial with negative Poisson's ratio, are potentially utilized in the realms of energy absorption and engineering structures. However, most of the existing auxetic materials either contain a large amount of rotational motion or still have gaps when fully folded, which is not conducive to lifting loads. Besides, their application is limited to flexible environments due to their single-folding mode. To overcome such limitations, a fully foldable mechanical metamaterial with isotropic auxeticity is proposed by utilizing the Sarrus mechanism, and a derivative multi-mode folding form is obtained in this paper. Then, the degrees-of-freedom (DOF), bistability, and kinematic characterizations are analyzed to show the performance of the proposed structures. Finally, the parameters of the proposed fully foldable mechanical metamaterials are discussed to simplify the structures. Some prototypes are fabricated to validate the effectiveness and performance of the proposed mechanical metamaterials. The proposed mechanical metamaterials have some merits, such as isotropic auxeticity, being fully folded to achieve dense compression, being bistable with load-bearing capacity, multi-mode folding form, and single-DOF, and they have versatile potential applications in complex environments requiring large deformation and flexible adaptation.

  • Elastostatic Performance Evaluation of a Full-Mobility Parallel-Kinematics Machine With Flexible Links
    on February 10, 2025 at 12:00 am

    AbstractThe subject of this article is the elastostatics of a novel three-limb, full-mobility parallel-kinematics machine (PKM) with flexible links, intended for high-frequency, small-amplitude operations. The objective is to establish the Cartesian stiffness model and performance indices capable of guiding the structural design of the machines of interest. We base our analysis on what we term an elastostatic Cartesian model: the light-weight limb rods are modeled as identical, massless, linearly elastic beams; the motor shafts and couplings are modeled likewise, with the beams replaced by identical, massless, linearly elastic torsional springs, both link flexibility and actuator flexibility thus being considered. The moving platform is assumed to be the only moving rigid body of the machine. This platform is thus regarded as a rigid body elastically mounted onto the base platform via a six-degree-of-freedom (six-DoF) Cartesian spring. Then, the PKM 6×6 Cartesian stiffness matrix, considering the flexibility of both limb rods and motor shafts, is derived via the pertinent kinetostatic relations. Moreover, three alternative indices are defined from this model to evaluate the robot stiffness, which allows us to choose the most appropriate one for specific applications.

  • Announcing the Journal of Mechanisms and Robotics 2023 Best Paper Award
    on February 10, 2025 at 12:00 am

    JMR Best Paper for 2023

  • Active Cables Selection for Collocated Vibration Control of Small-Sized Overconstrained Cable-Driven Parallel Robots
    on February 10, 2025 at 12:00 am

    AbstractCable-driven parallel robots (CDPRs) are well appreciated for high dynamics applications, due to their lightweights moving parts. Nevertheless, due to the low stiffness of cables, vibrations can occur and can degrade performances if high precision is required, such as in additive manufacturing for instance. Previous works have studied techniques to counteract vibrations, like using motor command or embedded devices. Based on a previous first exploration of using piezoelectric transducers on cables for this type of robot, this paper presents a proper formulation of the collocated active vibration control to damp the end-effector oscillations of small-sized overconstrained CDPRs by the measure of the variation in cable tensions. This goes through a modeling of such a robot with embedded piezoelectric transducers under appropriate assumptions. From this control formulation, it is shown that the collocated nature of these transducers are fundamental. It is thus possible to highlight an energetic index of active cables selection, regardless of the used control law. The proposed technique is developed theoretically and analyzed through simulations on an eight-cable robot.

Investigation on a Class of 2D Profile Amplified Stroke Dielectric Elastomer Actuators

Abstract

Dielectric elastomer actuators (DEAs) have been widely studied in soft robotics due to their muscle-like movements. Linear DEAs are typically tensioned using compression springs with positive stiffness or weights directly attached to the flexible film of the DEA. In this paper, a novel class of 2D profile linear DEAs (butterfly- and X-shaped linear DEAs) with compact structure is introduced, which, employing negative-stiffness mechanisms, can largely increase the stroke of the actuators. Then, a dynamic model of the proposed amplified-stroke linear DEAs (ASL-DEAs) is developed and used to predict the actuator stroke. The fabrication process of linear DEAs is presented. This, using compliant joints, 3D-printed links, and dielectric elastomer, allows for rapid and affordable production. The experimental validation of the butterfly- and X-shaped linear DEAs proved capable of increasing the stroke up to 32.7% and 24.0%, respectively, compared with the conventional design employing springs and constant weights. Finally, the dynamic model is validated against the experimental data of stroke amplitude and output force; errors smaller than 10.5% for a large stroke amplitude (60% of maximum stroke) and 10.5% on the output force are observed.

Read More

Journal of Mechanisms and Robotics Open Issues